Chamberlain Elite CSW200 Commercial Swing Gate Operator with two (2) 1/2 hp motors. One motor opens the gate and the other one closes it, unlike any other operator in the world. The Elite CSW-200-UL-DM™ uses a unique, patented, dual motor feature. Because of this feature the gate operator can function in less than ideal conditions, such as desert environments, and not overheat the motors. The Chamberlain Elite CSW-200-UL-DM™ gate operator is specified for use at heavily accessed high traffic areas such as multiple family communities with 250 or more homes in high ambient temperature applications.
|Specifications||Electrical Specifications: |
120 VAC Power Built-in 120 VAC power receptacle (NEMA 5-15).
Alarm If the gate hits a vehicle twice while opening or closing, the system will shut down and an alarm will sound for five minutes. After five minutes, the system will automatically reset itself. To reset the system manually, a reset button must be used.
Alternate Outputs With Omni Option board, three push button command control, burglar alarm input and output.
Burglar Alarm With Omni Option board, interfaces with existing home alarm or alarm output.
Motor Protection Entrapment sensor shuts off the motor after it reaches the stall amp for 3 seconds, reverses direction for several inches and stops.
Electronic Inputs Radio receiver, key switch, safety loop, center loop, telephone entry system, computer input, fire department key switch, and 3-push-button station.
ERD Sensor If the gate hits a vehicle while closing, it re-opens. If it hits a vehicle while opening, it stops, reverses 4 to 6 inches, and stops again.
Gate Traveling Time Adjusted by a precision mechanical device and electrical limit switch system.
Loop Detectors Easy to install, modular, plug in loop detector inputs for exit loop, center loop, and safety loop.
Master/Slave Precise, synchronized movement and communication between two gate operators using three wire RS-485 bi-directional technology.
Magnetic Lock With Omni Option board, magnetic lock system is incorporated, allowing easy addition of the MG1300 locking system to the gate.
Modular Board Uses LEDs to indicate all input and output functions of the gate operator.
Motor Drive Solid state electronic motor drive system is incorporated into the board.
Power Input Controls power input to the board with convenient switch.
Power Management Board includes electronic power management with over current shutdown and automatic recovery.
Soft Stop Gate travels through the cycle at normal speed and comes to a stop slowly for more accurate gate cycle. Equipped with integrated time delay for long mechanical life expectancy.
Spike Suppressors 20,000 Amps and near lightning protection with modular omni surge suppressor. Initial response time: 0.000000000001 seconds.
Push-Button Control On board gate operator control for close, stop and open.
Timer Adjustable timer can be set from 0-60 seconds.
Approval UL and ETL listed to the latest UL325 and UL991 specifications.
Chassis Constructed with .25 inch sanded, welded, and gold zinc plated sheet metal.
Cover High density polyethylene plastic and stainless steel for excellent heat and corrosion resistance.
Cycles 75 cycles per hour with a 600 pound gate.
Dimensions Length:20.5" x Width:15" x Height:28"
Emergency Release The gate is easily disconnected by turning the release handle. the best option is our DC-1000CSW.
Finish All metal parts are gold zinc plated for rust proof protection.
Gate Length 18 feet maximum gate length.
Motor 1/2 hp, instant reversing, 120VAC, 4 amp, 1625 rpm, with high speed ball bearings.
Output Shaft 2.5 inch cold rolled steel.
Shipping Weight 175 pounds.
Travel Speed 90° opening in 13-15 seconds.
Warranty Seven (7) years for single home use and five (5) years for commercial use.
Weight 160 Pounds
Weight Capacity 600 pounds maximum gate weight.
Reduction Two, 30-to-1 worm gears equal a 900-to-1 reduction. Both are lubricated in an oil bath.