FAAC introduces their new B680H, a hydraulic barrier gate operator sporting an impressive brushless motor! Designed for over 2,000,000 continuous cycles before needing any special maintenance. It's the first of it's kind. The switching power supply, with high energy efficiency and extended voltage range, ensures operation from 100VAC to 240VAC. The integrated speed/position sensor allows precise control of the movement and reversing of the barrier arm when an obstacle is detected. The counter-balance spring of the B680H has been tested for over 2 million cycles. The hydraulic pump with brushless motor guarantees the movement of long or short barrier arms at high speeds and continuous use (100% duty cycle). The optional battery backup solution ensures operation in case of power-failure. Any of the barrier arms for the FAAC B680H that exceed 20 feet long are made by joining 2 modules up to 26 feet to ease in transportation - once the modules have been assembled, the connection joint is invisible and optional LED lighting may be fixed to the entire length of the arm. All the barrier arms are windproof, round or elliptically profiled and are supplied with rubber protection on the bottom. The E680 microprocessor control board ensures integration of the B680H with advanced control systems. It has numerous programmable outputs/inputs and two integrated, high-sensitivity Loop Detectors. The housing is non load-bearing and may be easily removed, with the body post remaining in place, allowing access from 360 degrees while installing or servicing. It is available in stainless-steel or colored steel versions. The steel is available in four colors with 100-micron, epoxy zinc primer anti-corrosion treatment. Once the body has been installed, with the bracket and the barrier arm, the cover can be easily installed or removed. Get Your FAAC Barrier Gate Opener Today!
|Manufacturer's Warranty||2 Year Manufacturer's Warranty|
|Features||Simple, step-by-step mechanical setup Automatic control board setup with just 2 steps Easy to access control board DIN bar already fitted and spaced for further accessories Optional Battery backup Sectional barrier arms Reverse on contact Retrofitable with foundation plate of FAAC 620 and 640 barriers Hybrid technology: Hydraulic + Brushless motor Over 2,000,000 continuous use cycles without special maintenance Removable covers available in 4 colors or stainless steel Programmable opening speed: 1.5 seconds for 7.5 ft barrier arms up to 6 seconds for 27 ft Easy-to-program advanced control unit Integrated encoder (with reverse in the event of obstacle) Two integrated Loop Detectors Master/Slave logic Optional flashing LED traffic lights with anti-vandalism system and LED lights for barrier arm Compatible with 620 and 640 foundation plate|
|Specifications||Power supply voltage: 100 to 240 Vac 50 (60) Hz Max motor load: 240 W Accessories power supply: 24 VDC Max accessories load: 800 mA Protection fuses: 4 self-resetting Pause time: Programmable (from 0 to 4.1 min) Motor power: Programmable on 50 levels Motor speed: Programmable on 50 levels Terminal board inputs: Loop 1, Loop 2, Open, Close, Closing Safety, Stop, Emergency, Power Supply. 36VDC, Battery XBAT, BUS 2-Easy Connector inputs: Encoder, Bar release sensor, Integrated flashing light, USB (for updating firmware) Terminal board outputs: Flashing lamp 24V, Brushless motor, Accessories power supply 24 VDC, 4 programmable outputs (one with relay) Electric motor: Brushless 36 VDC Absorbed power: 240 W Absorbed current: 1.1 A (at 230 V) Motor rotation speed: 1,000 to 6,000 r.p.m. Pump flow rate: 3,2 l/min (max) Electronic deceleration: Absolute magnetic encoder Operating ambient temperature: -4°F - 131°F (-20°C - +55°C) Weight: 187 lb (143 lb body + 44 lb cover) Type of oil: FAAC HP OIL Barrier body treatment: 100 micron epoxy zinc-plating anti-corrosion treatment + paint|